How To Light A Gas Water Heater Video

First things first, try to light it again before assuming there is a major problem. Then press the igniter until the pilot lights.

On a gas water heater, the gas control valve contains the

The manufacturers standard re lighting steps must always be followed and then when it comes to igniting a pilot flame the bbq lighter performs the duty of what a piezo igniter could normally do.

How to light a gas water heater video. If playback doesn't begin shortly, try restarting your device. Hold the button down for as long as it tells you. If the pilot does not light, the water heater will not heat.

This will start the flow of gas so you can light the flame. If the pilot flame in your rheem 5 star gas water heater has gone out? You'll want to turn the knob past pilot to the off position.

If air manages to enter the lp or the liquid propane lines, it becomes a hindrance to the water heater, and it wont light. After pressing the igniter button the pilot should be alight, but continue to hold the control knob down for another 20 seconds. Turn the gas knob to pilot, press and hold it down.

First locate the temperature controls. Once the pilot is alight. This is where we can move on and check the interior door panel for the directions to find out how to turn on gas water heater pilot light.

Videos you watch may be added to the tv's watch history and influence tv recommendations. Two small gas tubes will lead to it. The below video will demonstrate how to light your water heater pilot light.

If your gas water heater has an igniting button, press that instead. If the pilot is restricted, try removing it and clearing it with a stiff brush and/or compressed air. Youll want to press and hold the knob down.

First, locate the gas valve on the front of the water heater, turn the thermostat all the way down to its lowest setting, usually the vacation setting is the lowest setting found on the dial. If the pilot cannot be cleaned, replace it. If you have trouble locating it, its usually located at the front of the water heater.

Please follow these instructions carefully: Now off the regulator valve. Youll want to watch it as you work.

This will allow the main burner to light whenever the water needs heating. Sometimes, carbon deposits can build up on the pilot and eventually create a restriction. Press the button down and ignite the flame inside the rectangular.

You will usually turn the dial to pilot and hold down the button. Keeping in mind that each water heater is unique and has instructions that you should reference, here we have general instructions on how to light a gas water heater. This small flame lights the main burner whenever water in the tank needs heating.

Hold the red button down while pressing the piezo ignitor striker, found to the immediate right of the gas knob, repeatedly until the pilot is lit. While holding the control button down, press the igniter button repeatedly for about 40 seconds. In older water heaters its called a thermocouple which is a heat sensing bulb attached to a copper capillary which connects to the fuel control valve.

We want to put the heat to the minimum. In case, the hot heater starts, you could conclude that air entrance is causing the real issue. This will start the flow of gas so you can light the.

In your rheem 5 star gas water heater there is a small pilot flame that should remain alight at all times. Hole using the gas lighter. How to light an automatic water heater the first step is turning off the gas by first looking for the knob labeled on/off/pilot.

Leave it like this for 1 minute. See the article ' following pilot light lighting instructions ' for information on how to locate the instructions and why it. Some water heaters have a separate button for pilot mode, usually a red one, which youll press and hold.

Read our simple step by step instructions below on how to relight the pilot light. Stop and start this rv water heater troubleshooting video at key points or back it up or fast forward it to quickly find the information you need. Remember, you can get all your water heater parts here at plumbersstock.

After 40 seconds, release the knob and check the pilot is. The pilot ignites the water heaters gas burner. While still holding the gas knob, light the pilot with a long lighter.

Once the pilot is alight it is important for your safety that you remove your face from directly in front of the combustion chamber opening. Using an open flame around natural gas can be very dangerous, so in this video we're going to show you how to safely relight a gas water heater. Push down the red button to the left of the gas knob.

Alternatively, watch the video at the bottom of the page. Lighting a gas water heater in 7 steps. Hold the red button down while pressing the piezo ignitor striker, found to the immediate right of the gas knob, repeatedly until the pilot is lit.

Once ignited, release and turn the gas knob to the on position and listen for the main burner to turn on. On some water heater models, you press and hold down a separate red button to start the pilot burner gas flow. To detect whether it is the air causing the problem, light the stove burners, and consequently switch on the rv water heater.

The pilot light in a gas water heater is made possible by either of two devices. Slide the button to the far left so it sits under the circle symbol. While still holding the gas down, light that.

How to Relight your Water Heater Pilot Light YouTube in